https://www.watercraftwerks.com     Call Us:  760-432-9900    Email Us:  wcwerks@pacbell.net

Quick Find:    
Categories
Custom Printed Parts
Hydro-Turf Traction Mats
Hydro-Turf Seat Covers
Freestyle and Freeride
Four Stroke
Accessories
Bilge
Body
Chemical
Driveline - Handling
Electrical
Engine Parts
Exhaust
Flush Kits
Fuel Systems
hardware
R&D Watercraft Performance Parts
Service Tools
Steering
wake-up kits
Waterline - Hardware
Used Watercraft Parts
ATV and MX
New OEM Parts
Misc New Watercraft Parts
Street Bike
Non PWC Items
Free & Misc Stuff with Order
Coming Soon
Articles
New Articles (0)
All Articles (14)
Aqua Performance Boarding Step ->
Hydro-Turf mat kits for jet skis, waverunners and sea doos (4)
Hydro-Turf Seat Covers for Jet Skis, Waverunners and Seadoos (1)
Jet Trim Spray Deflector Instructions (6)
Yamaha Jet Skis (1)
Kawasaki Jet Skis (2)
Cards We Accept
Cards We Accept
  Top » Catalog » Jet Trim Spray Deflector Instructions » Spray Deflector - Sea Doo Behind Bond Rail
Spray Deflector - Sea Doo Behind Bond Rail by Watercraft Werks

Spray Deflector : Instructions : Sea Doo: Behind Bond Rail

Tools needed: Power Drill, 3/16" Drill Bit, Tin Snips, 3/16" X 3/4" Pop Rivets, Rivet Gun, Screwdriver, Awl, Contact Cement, And Hot Glue.

The front bumper must be removed before the splash guard can be installed. In order to do this, first remove the four rivet caps. You can use a small flat blade screwdriver to pry out the rivet caps.
Use a 3/16" drill bit to drill out the four existing rivets that hold the front bumper in place.
Make sure all of the old rivets are removed.
Peel back the rub rail insert and drill out the first four rivets on each side of the hull. This will allow you to remove the rub rails partially. Around half way up the side.
Run the 3/16" drill bit through each of the holes. Be careful not to drill to far. You could drill through the hull of your craft. 
Find and mark the exact center of the bow.
Mark the center of the top edge of the splash guard.
Align the two marks and drill 3/16" hole and install one pop rivet. Drill 1/4" from edge of splash guard.
Hold splash guard into place one side at a time and punch holes where the stock rivets went. Be sure that the holes are not to close to the edge of the splash guard, allow at least 1/4".
Apply glue to back side of splash guard.
Drill and install one pop rivet on each end of splash guard. Now the splash guard is glued securley to the bond rail with one pop rivet in the front center and at least one on each end. Two would not hurt. 
Reattach the side rails using 3/16" pop rivets, and install the rub rail insert. 
Reinstall front bumper and rivet caps.

Now it is time for a nice dry ride and test your installation.

This article was published on Tuesday 20 January, 2015.
Current Reviews: 0  Write Review 
Tell a friend
Tell a friend about this article:     
Your Account
Your Email Address
Your Password
  
Shopping Cart more
0 items
Search
    
Use keywords to find the product you are looking for.
Advanced Search
Specials more
Skilock PL9 Nose Pin Lock for Jet Skis and Waverunners
Skilock PL9 Nose Pin Lock for Jet Skis and Waverunners
 $34.95  $19.95 
Information
2015 Hot Products Catalog
2014 Hot Products Catalog
2013 Hot Products Catalog
2012 Product Catalog
2011 Product Catalog
Privacy Policy
Terms of Use
Featured more
Hydro-Turf Sea Doo Challenger (01) Sportster DI (01-05) Mat Set
Hydro-Turf Sea Doo Challenger (01) Sportster DI (01-05) Mat Set
 $285.95