https://www.watercraftwerks.com     Call Us:  760-432-9900    Email Us:  wcwerks@pacbell.net

Quick Find:    
Categories
Custom Printed Parts
Hydro-Turf Traction Mats
Hydro-Turf Seat Covers
Freestyle and Freeride
Four Stroke
Accessories
Bilge
Body
Chemical
Driveline - Handling
Electrical
Engine Parts
Exhaust
Flush Kits
Fuel Systems
hardware
R&D Watercraft Performance Parts
Service Tools
Steering
wake-up kits
Waterline - Hardware
Used Watercraft Parts
ATV and MX
New OEM Parts
Misc New Watercraft Parts
Street Bike
Non PWC Items
Free & Misc Stuff with Order
Coming Soon
Articles
New Articles (0)
All Articles (14)
Aqua Performance Boarding Step ->
Hydro-Turf mat kits for jet skis, waverunners and sea doos (4)
Hydro-Turf Seat Covers for Jet Skis, Waverunners and Seadoos (1)
Jet Trim Spray Deflector Instructions (6)
Yamaha Jet Skis (1)
Kawasaki Jet Skis (2)
Cards We Accept
Cards We Accept
  Top » Catalog » Jet Trim Spray Deflector Instructions » Spray Deflector - Yamaha Between Bumper & Rail
Spray Deflector - Yamaha Between Bumper & Rail by Watercraft Werks

Spray Deflector : Instructions : Yamaha: Between Bumper & Rail

The front bumper must be removed before the splash guard can be installed. In order to do this, first remove the four nuts behind the bumper. Then pry the bumper off with a small screwdriver.

Remove insert from rub rail about half way up each side.
Remove enough screws to detach bumper about half way up each side. Use a small screwdriver or gasket scraper to detach bumper.
Run the 3/16" drill bit through each of the holes. Be careful not to drill to far. You could drill through the hull of your craft.
Find and mark the exact center of the bow.
Mark the center of the top edge of the splash guard.
Align the two marks and drill 1/16" hole and install one pop rivet. Drill 1/4" from edge of splash guard and 1/4" from edge of bumper.
Hold splash guard into place one side at a time and punch holes where the stock rivets went. Be sure that the holes are not to close to the edge of the splash guard, allow at least 1/4".
Apply glue on both sides of splash guard.
Lay bumper down into place and install pop rivets in each of the original holes.
Add at least one extra pop rivet on each end of splash guard. Two is better. Now the splash guard is glued securely to the back side of the bond rail. The side bumpers are back in place with pop rivet in all the original screw holes and at least one extra pop rivet on each end.
Reinstall side bumper insert. A rubber mallet works good.
Reinstall front bumper.

This article was published on Tuesday 20 January, 2015.
Current Reviews: 0  Write Review 
Tell a friend
Tell a friend about this article:     
Your Account
Your Email Address
Your Password
  
Shopping Cart more
0 items
Search
    
Use keywords to find the product you are looking for.
Advanced Search
Specials more
Skilock PL9 Nose Pin Lock for Jet Skis and Waverunners
Skilock PL9 Nose Pin Lock for Jet Skis and Waverunners
 $34.95  $19.95 
Information
2018 Hot Products Catalog
2017 Hot Products Catalog
2016 Hot Products Catalog
2015 Hot Products Catalog
2014 Hot Products Catalog
2013 Hot Products Catalog
2012 Product Catalog
2011 Product Catalog
Privacy Policy
Terms of Use
Featured more
Handlepole Spring Tensioner Kawasaki 750SX SXI Jet Ski
Handlepole Spring Tensioner Kawasaki 750SX SXI Jet Ski
 $27.95