https://www.watercraftwerks.com     Call Us:  760-432-9900    Email Us:  wcwerks@pacbell.net

Quick Find:    
Categories
Custom Printed Parts
Hydro-Turf Traction Mats
Hydro-Turf Seat Covers
Freestyle and Freeride
Four Stroke
Accessories
Bilge
Body
Chemical
Driveline - Handling
Electrical
Engine Parts
Exhaust
Flush Kits
Fuel Systems
hardware
R&D Watercraft Performance Parts
Service Tools
Steering
wake-up kits
Waterline - Hardware
Used Watercraft Parts
ATV and MX
New OEM Parts
Misc New Watercraft Parts
Street Bike
Non PWC Items
Free & Misc Stuff with Order
Coming Soon
Articles
New Articles (0)
All Articles (14)
Aqua Performance Boarding Step ->
Hydro-Turf mat kits for jet skis, waverunners and sea doos (4)
Hydro-Turf Seat Covers for Jet Skis, Waverunners and Seadoos (1)
Jet Trim Spray Deflector Instructions (6)
Yamaha Jet Skis (1)
Kawasaki Jet Skis (2)
Cards We Accept
Cards We Accept
  Top » Catalog » Hydro-Turf Seat Covers for Jet Skis, Waverunners and Seadoos » Installing your Hydro-Turf seat cover
Installing your Hydro-Turf seat cover by Watercraft Werks

Upholstery Installation

Please read through instructions before starting.

We recommend that someone experienced with upholstery install this cover using ¼ inch long stainless steel staples and an air powered staple gun. Galvanized staples can be used as a second choice, but may rust.

It is preferable to apply your Hydro-Turf upholstery directly over the old upholstery. Trim away any bunching of the old material on the under side, especially at the corners. However, the old upholstery may be removed completely if it is torn or has seams that will show through the new upholstery. You will also want to remove the old cover if the seat is wet (allow to sit with cover off until dry).

If a chunk of foam is torn out, you can use contact cement to glue a new piece in place. Sand it flush to match existing foam.

If possible, the new material should be warmed in the sun to increase flexibility and ease of installation. A blow dryer can also be used (be careful not to get material too hot). Sharp corners should be rounded with a file, and/or taped over with duct tape, to prevent cutting.

Align the Hydro-Turf Upholstery Kit to the seat/sides/chinpad contours and put 1 anchor staple at the back of each contour alignment point (corners and curves). Once the kit is correctly aligned and anchored, continue to tighten and staple kit securely to the under side of the seat. Cut away excessive bunching at corners. Extra staples can also flatten out bunching. Finally, trim away any excess material.

On some seat models, there is a strap. If so, follow these steps: Remove the strap via its screws or rivets (remove rivet by drilling off rivet head and pushing remainder through old seat). Save any mounting hardware for re-installation. Either: a) Cover the strap with the vinyl strip enclosed in your kit. (It should be sewn on using a heavy-duty sewing machine and synthetic thread). b) Install the original strap as is. c) Do not re-install the strap.

On some kits, a dash cover piece may be included. Applying some contact cement to this piece may allow you to get a better-contoured fit.

This article was published on .
Current Reviews: 0  Write Review 
Tell a friend
Tell a friend about this article:     
Your Account
Your Email Address
Your Password
  
Shopping Cart more
0 items
Search
    
Use keywords to find the product you are looking for.
Advanced Search
Specials more
Skilock PL9 Nose Pin Lock for Jet Skis and Waverunners
Skilock PL9 Nose Pin Lock for Jet Skis and Waverunners
 $34.95  $19.95 
Information
2015 Hot Products Catalog
2014 Hot Products Catalog
2013 Hot Products Catalog
2012 Product Catalog
2011 Product Catalog
Privacy Policy
Terms of Use
Featured more
Hot Products 2013 Catalog
Hot Products 2013 Catalog
 $0.00