https://www.watercraftwerks.com     Call Us:  760-432-9900    Email Us:  wcwerks@pacbell.net

Quick Find:    
Categories
Custom Printed Parts
Hydro-Turf Traction Mats
Hydro-Turf Seat Covers
Freestyle and Freeride
Four Stroke
Accessories
Bilge
Body
Chemical
Driveline - Handling
Electrical
Engine Parts
Exhaust
Flush Kits
Fuel Systems
hardware
R&D Watercraft Performance Parts
Service Tools
Steering
wake-up kits
Waterline - Hardware
Used Watercraft Parts
ATV and MX
New OEM Parts
Misc New Watercraft Parts
Street Bike
Non PWC Items
Free & Misc Stuff with Order
Coming Soon
Articles
New Articles (0)
All Articles (14)
Aqua Performance Boarding Step ->
Hydro-Turf mat kits for jet skis, waverunners and sea doos (4)
Hydro-Turf Seat Covers for Jet Skis, Waverunners and Seadoos (1)
Jet Trim Spray Deflector Instructions (6)
Yamaha Jet Skis (1)
Kawasaki Jet Skis (2)
Cards We Accept
Cards We Accept
Latest products more
Kawasaki 650 SX Horizontal Switch Housing
Kawasaki 650 SX Horizontal Switch Housing
 $80.00 
  Top » Catalog » Hydro-Turf mat kits for jet skis, waverunners and sea doos » Installing your Hydro-Turf mat kit with 3m self adhesive
Installing your Hydro-Turf mat kit with 3m self adhesive by Watercraft Werks

Mats with Self-Adhesive

Please read through instructions before starting.

Installation

1.Prior to removing the paper backing, position all mat pieces. This will help insure proper location and fit. Tracing along the outside edge in pencil will help give you a guide to make sure you are installing the mat kit in the proper position.

2.Remove the old mats (if applicable) and clean the area where the new mats will go. Make sure the surface is free of dirt and oil. A solvent such as acetone or alcohol works well. Be sure to work in a well-ventilated area.

3.If your mat has a die cut logo in it, the logo should be left in the mat to ensure proper fit. Taping the top side of the logo will help hold it in place during installation.

4.You are now ready to glue down your new Hydro-Turf mats. Double check to make sure area is dry and free of dirt, oil or old glue. Work with one piece at a time. Using two people for the larger pieces will make installation easier. Peel off paper backing and gently position mat in place, do not apply pressure yet so the mat can be repositioned if necessary.

5.Once the mat is correctly positioned, apply firm pressure. Work from the center to the outer edges. This is a pressure sensitive adhesive, so put as much weight into as you can. Use a small rolling pin or similar round object to go over the surface of the mat paying attention to the edges of the kit to ensure a good bond.

6.After 24 hour the mat kit is 85% cure and can be used. Self Adhesive cures 100% after 48 hrs..

Care Tips

1.Do not place your mats in the sun prior to installation, they will shrink and will become unusable.

2.Always store your craft in a shaded area or use a PWC cover when not in use

3.Should your Hydro-Turf get dirty it can be cleaned using any soap or cleanser and a brush. Be sure to rinse thoroughly, as any leftover residue can make a slippery surface.

This article was published on .
Current Reviews: 0  Write Review 
Tell a friend
Tell a friend about this article:     
Your Account
Your Email Address
Your Password
  
Shopping Cart more
0 items
Search
    
Use keywords to find the product you are looking for.
Advanced Search
Specials more
Skilock PL9 Nose Pin Lock for Jet Skis and Waverunners
Skilock PL9 Nose Pin Lock for Jet Skis and Waverunners
 $34.95  $19.95 
Information
2015 Hot Products Catalog
2014 Hot Products Catalog
2013 Hot Products Catalog
2012 Product Catalog
2011 Product Catalog
Privacy Policy
Terms of Use
Featured more
Hydro-Turf Sea Doo Challenger (01) Sportster DI (01-05) Mat Set
Hydro-Turf Sea Doo Challenger (01) Sportster DI (01-05) Mat Set
 $285.95